The Foxtrot 2 series offers several variants of basic modules in an "open-frame" design, along with corresponding peripheral modules. These modules are designed to accommodate customer-defined input and output parameters, with a selection of measured signals and various output options available. For example, various temperature sensors (NTC, PTC, Pt, Ni, TC), measurement of standard quantities (10 V, 5 V, 2 V, 1 V, 20 mA, 10 mA), resistance measurement, and less typical values, such as voltage inputs up to 70 VDC, as well as PWM and counter inputs, relay outputs with 5 A contacts, 16 A, 230 VAC SSR relays, 24 VDC transistor outputs with stepper motor control capability, PWM outputs, etc. A more detailed description of the CP-2970 is available in this article.
Specific options must always be addressed on an individual basis. The modules are designed for series production as OEM components for the customer’s end product.
CP-2970
The standard Foxtrot OEM PLC series with the following possible configurations:
Up to 20 x AI, DI: resistive temperature sensors, safety contacts, 24V DI, counters, PWM, voltage, current, etc.
Up to 6x AO 10 V, of which up to 4x can be PWM outputs
Up to 16x RO 5A contacts; can be configured with a combination of 16 A RO (max 6) and 5 A RO (4x)
2x EEV bipolar or unipolar 24 V
1x DI 230 VAC
Optional submodule expansion: 8x DI 24V or 8x DO 24V, 2x EEV, 4x RO 5A, and more…
2x Ethernet, 2x USB, CIB, TCL2, up to 3x RS-485 or RS-232
Power supply: 24 VDC or 230 VAC
Dimensions: 190 × 140 × (33 ÷ 47) mm (depth may be greater, depending on configuration)
For a more detailed description, click HERE
CP-2940
a smaller variant of the system derived from the CP-2970
Up to 12 x AI, DI: resistance temperature sensors, safety contacts, 24 V DI, counters, PWM, voltage, current, etc.
Up to 4 x AO 10 V, of which up to 4 can be PWM outputs
Up to 12 x RO 5 A contacts; can be configured with a combination of 16 A RO (max. 6)
2x EEV bipolar or unipolar 24V
2x DI 230 VAC
optional submodule expansion: 8x DI 24V or 8x DO 24V, 2x EEV, 4x RO 5A, and more…
2x ETH, 2x USB, CIB, TCL2, up to 3x RS-485 or RS-232
24 VDC or 230 VAC power supply
Dimensions: 158 × 116 × 33 mm
C-OE-3970
Standard range of OEM peripheral modules for the CIB bus (versions for the TCL2 bus are also available)
Up to 12 x AI, DI: resistive temperature sensors, safety contacts, 24V DI, counters, PWM, voltage, current, etc.
Up to 4x AO 10 V, of which up to 4x can be PWM outputs
Up to 12x RO 5A contacts; can be configured with a combination of 16 A RO (max 6)
2x EEV bipolar or unipolar 24V
2x DI 230 VAC
Optional expansion via submodule: 8x DI 24V or 8x DO 24V, 2x EEV, 4x RO 5A, and more…
Power supply: 24 VDC or 230 VAC
Dimensions: 158 × 116 × 33 mm
Coming soon:
CP-2770
New Foxtrot range, drive-less version
New processor module, 1x Ethernet, up to 5x RS-485 (or 3x RS-232)
Standard version designed for Zone 2 (heat pump with R290 refrigerant)
Dimensions based on the CP-2970 series
C-OE-3801D with variable peripheral submodules
e.g., for heating system control (heat pump indoor unit), energy metering, etc.
Base unit with 5x AI/DI and 3x DO, with slots for up to 5x modules that function as CIB modules with a fixed address (the base unit also has a fixed CIB address)
Power supply for the entire assembly from 230 VAC or 24 VDC
Smaller version supporting a smaller number of submodules; only a carrier board for submodules
CIB submodule for variable OEM peripherals
Various configuration and application options; based on a 2x 5-pin connector, module width 25 mm
Submodule configurations currently under consideration:
4x AI/DI and 3x RO 5 A
4x AI/DI and 2x RO 16 A
4x AI/DI and one relay power output, more than 16 A, not yet specified
Fast 1-phase electricity meter module (3-phase variant not yet addressed)